For...Next
 
Control flow statement for looping

Syntax

For iterator [ As datatype ] = startvalue To endvalue [ Step stepvalue ]
[ statement block ]
Next [ iterator ]

Parameters

iterator
a variable identifier that is used to iterate from an initial value to an end value
datatype
If specified, the variable iterator will automatically be declared with the type datatype
startvalue
an expression that denotes the starting value of the iterator
endvalue
an expression used to compare with the value of the iterator
stepvalue
an expression that is added to the iterator after every iteration

Description

A For...Next loop initializes iterator to startvalue, then executes the statement block, incrementing iterator by stepvalue until it exceeds endvalue. If stepvalue is not explicitly given it will set to 1.

The values of stepvalue and endvalue are stored internally immediately following execution of the For statement and thus neither can be changed inside the For loop. Comparison operators such as < and > will not be effective as stepvalue or endvalue because the expressions will not be re-evaluated while the loop is running. (The results of the expressions used to define them may be changed, but these changes will not affect the execution of the For loop.) See examples.

Note: In some dialects, the temporary variables holding stepvalue and endvalue go out of scope at the end of the loop, and their values are not guaranteed to remain unchanged once any code following the loop has been executed. For this reason, it is recommended never to branch out of a For...Next loop (using Goto or similar), and then jump back into the middle of it later when in the -lang fb or -lang deprecated dialect.

The iterator must be an intrinsic scalar: only Static/Shared variables and local variables can be used; no other kind can be used, including array elements, UDT members, ByRef parameters or any kind of dereferenced address.

The iterator may be defined having the same scope as the For statement by using the As datatype syntax. With this syntax, iterator is created and destroyed within the For...Next scope. See dialect differences below.

If endvalue is less than startvalue then a negative stepvalue must be specified or the statement block will not execute at all, since startvalue compares greater than endvalue.

The For statement causes the execution of the statements in the statement block until iterator compares greater than endvalue (or less than endvalue if stepvalue < 0). iterator will be incremented the amount of stepvalue following each execution of the statement block. If an increment is not given, iterator will be implicitly incremented by 1.

If an Exit For statement is encountered inside the statement block, the loop is terminated, and execution resumes immediately following the enclosing Next statement. If a Continue For statement is encountered, the rest of the statement block is skipped until the block's corresponding Next statement. The counter's value is incremented and the loop restarted if it is still within the bounds given by endvalue.

Note: for integer data types, it is not possible to loop up to the highest possible value (or down to the lowest possible value) that can be stored in the variable type, because the loop only breaks when the incremented variable exceeds endvalue, which can never happen. For example, if you try to iterate an variable from 0 to 255, the loop will only break once the variable reaches 256 or more. Using a UByte variable for the counter wouldn't work, because although it can hold the numbers 0 to 255, it cannot hold 256. See Standard Data Type Limits to find the upper and lower limits for the standard data types.

Like all control flow statements, the For statement can be nested, that is, it can be used in a statement block of another For statement.

For, Next, and Step are operators that can be overloaded inside user defined types. See Operator For, Operator Next, Operator Step

Example

Print "counting from 3 to 0, with a step of -0.5"
For i As Single = 3 To 0 Step -0.5
    Print "i is " & i
Next i

Dim As Integer i, j, k, toTemp, stepTemp
j = 9: k = 1

For i = 0 To j Step k
    
    j = 0: k = 0 '' Changing j and k has no effect on the current loop.
    Print i;
    
Next i
Print

' Internally, this is what the above example does:
j = 9: k = 1

i = 0: toTemp = j: stepTemp = k
Do While IIf(stepTemp >= 0, i <= toTemp, i >= toTemp)
    
    j = 0: k = 0 '' Changing j and k has no effect on the current loop.
    Print i;
    
    i += stepTemp
Loop
Print


Dialect Differences

  • In the -lang fb and -lang deprecated dialects, variables declared inside a For..Next block are visible only inside the block, and cannot be accessed outside it.
  • In the -lang qb and -lang fblite dialects, variables declared inside a For..Next block (including the counter if declared, and any temporary variables used to hold endvalue or stepvalue), have a procedure-wide scope as in QB

Differences from QB

  • ByRef arguments cannot be used as counters.

See also